[Free] 2018(May) EnsurePass Dumpsleader Cisco 400-151 Dumps with VCE and PDF 151-160

Ensurepass.com : Ensure you pass the IT Exams
2018 May Cisco Official New Released 400-151
100% Free Download! 100% Pass Guaranteed!

CCIE Data Center (v2.0)

Question No: 151 – (Topic 2)

Refer to the exhibit.

Ensurepass 2018 PDF and VCE

Based on this portion of an MDS iSCSI configuration, which two statements are true? (Choose two)

  1. The fc-lun 0x0000 mapping to iscsi-lun 0x0000 is not permitted.

  2. The iSCSI initiator that connects to target name iqn.1987-02.com.cisco.t3 will see two LUNs numbered as 2 and 4.

  3. The iSCSI initiator and the iSCSI target iqn.1987-02.com.cisco.t3 must be in the same zone before LUNs are available to the host.

  4. The iSCSI initiator at name iqn.1987-02.com.cisco.t2 has access to only one LUN.

  5. The iSCSI initiator that connects to target name iqn.1987-02.com.cisco.t3 will see two LUNs as numbers 0 and 1.

Answer: C,E

Question No: 152 – (Topic 2)

SNMPv3 authorizes management operations only by configured users and encrypts SNMP messages. Which authentication protocols does Cisco NX-OS Software use for SNMPv3? (Choose two.)

  1. NMAC-SHA-96 authentication protocol

  2. HMAC-MD5-96 authentication protocol

  3. Community String Match protocol

  4. NMAC-MD5-96 authentication protocol

  5. HMAC-SHA-96 authentication protocol

Answer: B,E

Question No: 153 – (Topic 2)

Assuming the local peer is 10.0.0.1 and the remote peer (configuration not shown) is 10.0.0.2, which of these is used to configure PIM Anycast-RP on a Nexus 7000 switch?

  1. feature pim! interface loopback1

    ip address 10.0.0.1/32

    ip router ospf 10 area 0.0.0.0 ip pim sparse-mode

    !

    interface loopback2 ip address 2.2.2.2/32

    ip router ospf 10 area 0.0.0.0 ip pim sparse-mode

    !

    ip pim anycast-rp 2.2.2.2 10.0.0.1

    ip pim anycast-rp 2.2.2.2 10.0.0.2

    ip pim rp-address 2.2.2.2 group-list 224.0.0.0/4

  2. feature pim

    !

    interface loopback1

    ip address 10.0.0.1/32

    ip router ospf 10 area 0.0.0.0 ip pim sparse-mode

    !

    interface loopback2 ip address 2.2.2.2/32

    ip router ospf 10 area 0.0.0.0 ip pim sparse-mode

    !

    ip pim anycast-rp 10.0.0.1 2.2.2.2

    ip pim anycast-rp 10.0.0.2 2.2.2.2

    ip pim rp-address 2.2.2.2 group-list 224.0.0.0/4

  3. interface loopback1 ip address 10.0.0.1/32

    ip router ospf 10 area 0.0.0.0 ip pim sparse-mode

    !

    interface loopback2 ip address 2.2.2.2/32

    ip router ospf 10 area 0.0.0.0 ip pim sparse-mode

    !

    ip pim anycast-rp 2.2.2.2 10.0.0.1

    ip pim anycast-rp 2.2.2.2 10.0.0.2

    ip pim rp-address 2.2.2.2 group-list 224.0.0.0/4

  4. feature pim feature msdp

!

interface loopback1

ip address 10.0.0.1/32

ip router ospf 10 area 0.0.0.0 ip pim sparse-mode

!

interface loopback2 ip address 2.2.2.2/32

ip router ospf 10 area 0.0.0.0 ip pim sparse-mode

!

ip msdp originator-id loopback1

ip msdp peer 10.0.0.2 connect-source loopback1 ip msdp description 10.0.0.2 To 7010-2

ip msdp password 10.0.0.2 mypassword

!

ip pim rp-address 2.2.2.2 group-list 224.0.0.0/4

Answer: A

Question No: 154 – (Topic 2)

Refer to the Exhibit.

Ensurepass 2018 PDF and VCE

Which statement is true?

  1. The service profile in organization IS-SecureESX10 is trying to be associated to chassis 1 blade 7.

  2. The error is triggered when the service profile pn is being associated.

  3. The only way to fix the problem is to delete the service profile and start again with the proper MAC and WWPN pool association.

  4. If you ignore the warning and press Yes, the association fails because no MAC address is assigned.

Answer: D

Question No: 155 – (Topic 2)

Refer to the exhibit.

Ensurepass 2018 PDF and VCE

ABC company has successfully implemented the smart call home.

Which three configuration components for CallHome are mandatory? (Choose threE.

  1. periodic inventory interval

  2. alert group to collect output

  3. destination profile

  4. email server and from email address

  5. contact information

  6. system contact Answer: D,E,F

Question No: 156 – (Topic 2)

Refer to the exhibit.

Ensurepass 2018 PDF and VCE

Which statement about the procedure to verify that the VSM is connected to vCenter Server is true?

  1. Install a new extension key and unregister the old extension key.

  2. Unregister the old extension key and install a new extension key

  3. Unregister the extension key.

  4. Install a new extension key.

  5. Issue no connect and connect commands. Answer: B

Question No: 157 – (Topic 2)

Refer to the exhibit.

Ensurepass 2018 PDF and VCE

Which three levels of protection for the CoPP policy option from the initial setup utility are valid (Choose three.)

  1. lenient

  2. major

  3. none

  4. minor

  5. aggressive

  6. moderate

Answer: A,C,F

Explanation: Ref: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/4_1/nx- os/security/configuration/guide/sec_nx-os-cfg/sec_cppolicing.html

Question No: 158 – (Topic 2)

Which three statements about Cisco UCS Fabric Interconnect fibre channel end-host mode are true? (Choose threE.

  1. The Cisco UCS Fabric Interconnect send BPDUs northbound.

  2. The Cisco UCS Fabric Interconnect learns southbound dynamic MAC addresses.

  3. The Cisco UCS Fabric Interconnect learns dynamic MAC addresses from attached storage fibre channel ports.

  4. The Cisco UCS Fabric Interconnect never learns northbound dynamic MAC addresses.

  5. Link status changes on uplink ports are propagated to host vNICs.

  6. vNIC fabric failover is never available in end-host mode.

  7. vHBA fabric failover is enabled by default.

Answer: B,C,E

Question No: 159 – (Topic 2)

Which three statements about the system port profiles are true? (Choose threE.

  1. A system port profile cannot be converted to a port profile that is not a system port profile.

  2. System VLANs cannot be added to a port profile.

  3. In a single ESX host, one VLAN can be a system VLAN on one port but a regular VLAN on another.

  4. A system port profile must be converted to a port profile that is not a system port profile.

  5. The native VLAN on a system port profile cannot be a system VLAN.

  6. A system port profile must be of the Ethernet type because it is used for physical ports.

Answer: A,C,F Explanation:

Ref:http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus1000/sw/4_2_1_s_v_1

_4/port_profile/configuration/guide/n1000v_port_profile/n1000v_portprof_4system.html#wp xref25626

PFC

Question No: 160 DRAG DROP – (Topic 2)

Drag and drop sequence of the steps on left for ISSU software of dual supervisor switches to achieve a non-disruptive upgrade on the right.

Ensurepass 2018 PDF and VCE

Answer:

Ensurepass 2018 PDF and VCE

100% Ensurepass Free Download!
Download Free Demo:400-151 Demo PDF
100% Ensurepass Free Guaranteed!
Download 2018 EnsurePass 400-151 Full Exam PDF and VCE

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

Your email address will not be published. Required fields are marked *